A submarine power cable is a transmission cable for carrying electric power below the surface of the water. These are called "submarine" because they usually carry electric power beneath salt water (arms of the ocean, seas, straits, etc.) but it is also possible to use submarine power cables beneath fresh water (large lakes and rivers). Examples of the latter exist that connect the mainland with large islands in the St. Lawrence River.
As key tools in bulk power transmission, submarine power tables tend to operate at high voltage in order to minimize resistive losses between the endpoints. Unlike overhead powerlines, many submarine power cables tend to operate with DC current. Electrical phases must endure close proximity inside the cable, increasing parasitic capacitance. It is more economical to use AC only with lines shorter than 100 km in length, in which case losses at the landing point grid interfaces dominate.
When the reasons for high voltage transmission, the preference for AC, and for capacitive currents are combined, one can understand why there are no underwater high electric power cables longer than 1000 km (see the table in "Operational submarine power cables" section below).
As indicated above, submarine power cables transport electric current at high voltage. The electric core is a concentric assembly of inner conductor, electric insulation, and protective layers (resembling the design of a coaxial cable). Modern three-core cables (e.g. for the connection of offshore wind turbines) often carry optical fibers for data transmission or temperature measurement, in addition to the electrical conductors. The conductor is made from copper or aluminum wires, the latter material having a small but increasing market share. Conductor sizes ⤠1200 mm<sup>2</sup> are most common, but sizes âÂÂ¥ 2400 mm<sup>2</sup> have been made occasionally. For voltages âÂÂ¥ 12 kV the conductors are round so that the insulation is exposed to a uniform electric field gradient. The conductor can be stranded from individual round wires or can be a single solid wire. In some designs, profiled wires (keystone wires) are laid up to form a round conductor with very small interstices between the wires.
Three different types of electric insulation around the conductor are mainly used today. Cross-linked polyethylene (XLPE) is used up to 420 kV system voltage. It is produced by extrusion, with an insulation thickness of up to about 30 mm; 36 kV class cables have only 5.5 â 8 mm insulation thickness. Certain formulations of XLPE insulation can also be used for DC. Low-pressure oil-filled cables have an insulation lapped from paper strips. The entire cable core is impregnated with a low-viscosity insulation fluid (mineral oil or synthetic). A central oil channel in the conductor facilitates oil flow in cables up to 525 kV for when the cable gets warm but rarely used in submarine cables due to oil pollution risk with cable damage. Mass-impregnated cables have also a paper-lapped insulation but the impregnation compound is highly viscous and does not exit when the cable is damaged. Mass-impregnated insulation can be used for massive HVDC cables up to 525 kV.
Cables âÂÂ¥ 52 kV are equipped with an extruded lead sheath to prevent water intrusion. No other materials have been accepted so far. The lead alloy is extruded onto the insulation in long lengths (over 50 km is possible). In this stage the product is called cable core. In single-core cables the core is surrounded by concentric armoring. In three-core cables, three cable cores are laid-up in a spiral configuration before the armoring is applied. The armoring consists most often of steel wires, soaked in bitumen for corrosion protection. Since the alternating magnetic field in AC cables causes losses in the armoring, those cables are sometimes equipped with non-magnetic metallic materials (stainless steel, copper, brass).
Alternating-current (AC) submarine cable systems for transmitting lower amounts of three-phase electric power can be constructed with three-core cables in which all three insulated conductors are placed into a single underwater cable. Most offshore-to-shore wind-farm cables are constructed this way.
For larger amounts of transmitted power, the AC systems are composed of three separate single-core underwater cables, each containing just one insulated conductor and carrying one phase of the three phase electric current. A fourth identical cable is often added in parallel with the other three, simply as a spare in case one of the three primary cables is damaged and needs to be replaced. This damage can happen, for example, from a ship's anchor carelessly dropped onto it. The fourth cable can substitute for any one of the other three, given the proper electrical switching system.