Ductwork airtightness can be defined as the resistance to inward or outward air leakage through the ductwork envelope (or ductwork shell). This air leakage is driven by differential pressures across the ductwork envelope due to the combined effects of stack and fan operation (in case of a mechanical ventilation system).
For a given HVAC system, the term ductwork refers to the set of ducts and fittings (tees, reducers, bends, etc.) that are used to supply the air to or extract the air from the conditioned spaces. It does not include components such as air handlers, heat recovery units, air terminal devices, coils. However, attenuators, dampers, access panels, etc. are a part of the ductwork even if they have more functions than conveying the air and are therefore also referred to as technical ductwork products.
Ductwork airtightness is the fundamental ductwork property that impacts the uncontrolled leakage of air through duct leaks.
There are two major systems to classify ductwork airtightness, one based on European standards, the other based on ASHRAE standard 90.1-2010. Both are based on the leakage airflow rate at a given ductwork pressure divided by the product of the ductwork surface area and the same ductwork pressure raised to the power 0.65.
In future revisions of EN 12237, EN 1507, EN 1751 and EN 15727 these new names will be used; they have already been introduced in EN 17192.
The relationship between pressure and leakage air flow rate is defined by the power law model between the airflow rate and the pressure difference across the ductwork envelope as follows:
q<sub>L</sub>=C<sub>L</sub>âÂÂp<sup>n</sup>
where:
This law enables to assess the airflow rate at any pressure difference regardless the initial measurement. Threshold limits in ductwork airtightness classifications usually assume an airflow exponent of 0,65.
The ductwork airtightness level is the airflow rate through ductwork leakages divided by the ductwork area. It is recommended to test at least 10% and 10 m<sup>2</sup> of the duct surface including all duct types and a variety of sizes and components. The ductwork surface area is estimated according to EN 14239.
The airflow rate through leakage can be measured by temporarily connecting a device (sometimes called a duct leakage tester to pressurize the ductwork including duct-mounted components. Air flow through the pressurizing device creates an internal, uniform, static pressure within the ductwork. The aim of this type of measurement is to relate the pressure differential across the ductwork to the air flow rate required to produce it. Generally, the higher the air flow rate required to produce a given pressure difference, the less airtight the ductwork. This pressurization technique is described in standard test methods such as EN 12599 and ASHRAE standard 90.1-2010. In principle, it is similar to that used to characterize building airtightness.
An airtight ductwork has several positive impacts:
Duct leakage affects more severely the energy efficiency of systems that include air heating or cooling.
At construction stage, the airtightness of individual components depends on the design (rectangular or round ducts, pressed or segmented bends, etc.) and assembly (seam type and welding quality). Components with factory-fitted sealing devices (e.g., gaskets, clips) meant to ease and accelerate the installation process are widely used in Scandinavian countries. A variety of techniques are widely used to tighten duct systems on site, including gaskets, tapes, sealing compound (mastic), internal duct lining, aerosol duct sealing. So-called "duct tapes" are often not suited for sealing ducts, which explains why, in the US, the International Energy Conservation Code (IECC) requires any tape used on duct board or flexible ducts to be labeled in accordance with UL 181A or 181B.
Typical reasons for poor ductwork air tightness include:
Sweden is often considered as a reference for airtight ducts: the requirements introduced in AMA (General material and workmanship specifications) starting in 1950 have led to excellent ductwork airtightness on a regular basis in Sweden.
In the US, there has been a significant amount of work showing energy saving potentials on the order of 20-30% in homes; and 10-40% in commercial buildings with airtight ducts
The ASIEPI project technical report on building and ductwork air tightness estimated the heating energy impact of duct leakage in a ventilation system on the order of 0-5 kWh per m<sup>2</sup> of floor area per year plus additional fan energy use for a moderately cold European region (2500 degree-days).