Bearing pressure is a particular case of contact mechanics often occurring in cases where a convex surface (male cylinder or sphere) contacts a concave surface (female cylinder or sphere: bore or hemispherical cup). Excessive contact pressure can lead to a typical bearing failure such as a plastic deformation similar to peening. This problem is also referred to as bearing resistance.
A contact between a male part (convex) and a female part (concave) is considered when the radii of curvature are close to one another. There is no tightening and the joint slides with no friction therefore, the contact forces are normal to the tangent of the contact surface.
Moreover, bearing pressure is restricted to the case where the charge can be described by a radial force pointing towards the center of the joint.
In the case of a revolute joint or of a hinge joint, there is a contact between a male cylinder and a female cylinder. The complexity depends on the situation, and three cases are distinguished:
By "negligible clearance", H7/g6 fit is typically meant.
The axes of the cylinders are along the z-axis, and two external forces apply to the male cylinder:
The main concern is the contact pressure with the bore, which is uniformly distributed along the z-axis.
Notation:
In this first modeling, the pressure is uniform. It is equal to:
If it is considered that the parts deform elastically, then the contact pressure is no longer uniform and transforms to a sinusoidal repartition:
with
This is a particular case of the following section (ø<sub>0</sub> = ÃÂ/2).
The maximum pressure is 4/àâ 1.27 times bigger than the case of uniform pressure.
In cases where the clearance can not be neglected, the contact between the male part is no longer the whole half-cylinder surface but is limited to a 2ø<sub>0</sub> angle. The pressure follows Hooke's law:
where
The pressure varies as:
where A and B are positive real number. The maximum pressure is:
the angle ø<sub>0</sub> is in radians.
The rigidity coefficient K and the half contact angle ø<sub>0</sub> can not be derived from the theory. They must be measured. For a given system â given diameters and materials âÂÂ, thus for given K and clearance j values, it is possible to obtain a curve ø<sub>0</sub> = ÃÂ(F/(DL)).
A sphere-sphere contact corresponds to a spherical joint (socket/ball), such as a ball jointed cylinder saddle. It can also describe the situation of bearing balls.
The case is similar as above: when the parts are considered as rigid bodies and the clearance can be neglected, then the pressure is supposed to be uniform. It can also be calculated considering the projected area:
As in the case of cylinder-cylinder contact, when the parts are modeled as elastic bodies with a negligible clearance, then the pressure can be modeled with a sinusoidal repartition:
with
When the clearance can not be neglected, it is then necessary to know the value of the half contact angle ø<sub>0</sub> , which can not be determined in a simple way and must be measured. When this value is not available, the Hertz contact theory can be used.
The Hertz theory is normally only valid when the surfaces can not conform, or in other terms, can not fit each other by elastic deformation; one surface must be convex, the other one must be also convex plane. This is not the case here, as the outer cylinder is concave, so the results must be considered with great care. The approximation is only valid when the inner radius of the container R<sub>1</sub> is far greater than the outer radius of the content R<sub>2</sub>, in which case the surface container is then seen as flat by the content. However, in all cases, the pressure that is calculated with the Hertz theory is greater than the actual pressure (because the contact surface of the model is smaller than the real contact surface), which affords designers with a safety margin for their design.
In this theory, the radius of the female part (concave) is negative.
A relative diameter of curvature is defined:
where d<sub>1</sub> is the diameter of the male part (positive) and d<sub>2</sub> is the diameter of the female part (negative). An equivalent module of elasticity is also defined:
where ý<sub>i</sub> is the Poisson's ratio of the material of the part i and E<sub>i</sub> its Young's modulus.
For a cylinder-cylinder contact, the width of the contact surface is:
and the maximal pressure is in the middle:
In case of a sphere-sphere contact, the contact surface is a disk whose radius is:
and the maximal pressure is in the middle:
In a bolted connection, the role of the bolts is normally to press one parts on the other; the adherence (friction) is opposed to the tangent forces and prevents the parts from sliding apart. In some cases however, the adherence is not sufficient. The bolts then play the role of stops: the screws endure shear stress whereas the hole endure bearing pressure.
In order to increase the bearing pressure of a material, there are several factors that can be considered. One of the most effective methods is to increase the surface area of the material. By increasing the surface area, the load is distributed over a larger area, reducing the bearing pressure.
In good design practice, the threaded part of the screw should be small and only the smooth part should be in contact with the plates; in the case of a shoulder screw, the clearance between the screw and the hole is very small ( a case of rigid bodies with negligible clearance). If the acceptable pressure limit P<sub>lim</sub> of the material is known, the thickness t of the part and the diameter d of the screw, then the maximum acceptable tangent force for one bolt F<sub>b, Rd</sub> (design bearing resistance per bolt) is:
In this case, the acceptable pressure limit is calculated from the ultimate tensile stress f<sub>u</sub> and factors of safety, according to the Eurocode 3 standard. In the case of two plates with a single overlap and one row of bolts, the formula is:
where
In more complex situations, the formula is:
where
fasteners,
When the parts are in wood, the acceptable limit pressure is about 4 to 8.5 MPa.
In plain bearings, the shaft is usually in contact with a bushing (sleeve or flanged) to reduce friction. When the rotation is slow and the load is radial, the model of uniform pressure can be used (small deformations and clearance).
The product of the bearing pressure times the circumferential sliding speed, called load factor PV, is an estimation of the resistance capacity of the material against the frictional heating.