Electrical wiring in North America refers to the practices and standards utilised in constructing electrical installations within domestic, commercial, and industrial sector buildings, and other structures and locations, within the region of North America. This does not include the topics of electrical power transmission and distribution.
Although much of the electrician's field terminology matches that of the electrical codes, usage can vary:
The United States National Electrical Code (NEC) specifies minimum acceptable wiring methods and materials for many states and municipalities. It is sponsored by the National Fire Protection Association (NFPA) and has been periodically revised since 1897. Local jurisdictions usually adopt the NEC or another published code and then distribute documents describing how local codes vary from the published codes. Governments cannot distribute the NEC itself for copyright reasons, though parts that have been adopted into law are not subject to copyright.
The purpose of the NEC is to protect persons and property from hazards arising from the use of electricity. The NEC is not any jurisdiction's electrical code per se; rather, it is an influential work of standards that local legislators (city council members, state legislators, etc. as appropriate) tend to use as a guide when enacting local electrical codes. The NFPA states that excerpts quoted from the National Electrical Code must have a disclaimer indicating that the excerpt is not the complete and authoritative position of the NFPA and that the original NEC document must be consulted as the definitive reference.
New construction, additions or major modifications of or to a building must follow the relevant code for the relevant jurisdiction, which is not necessarily the latest version of the NEC. Regulations in each jurisdiction will indicate when a change to an existing installation is so great that it must then be rebuilt to comply with the current electrical code. Generally existing installations are not required to be changed to meet new codes.
Other code requirements vary by jurisdiction in the United States. In many areas, a homeowner, for example, can perform household wiring for a building which the owner occupies. A few cities have more restrictive rules and require electrical installation work to be done by licensed electricians. The work will be inspected by a designated authority at several stages before permission is obtained to energize the wiring from the local electric utility. The inspector may be an employee of the state or city, or an employee of an electrical supply utility.
For electrical wiring in Canada, the Canadian Electrical Code is a very similar standard to that of the United States, published by the Canadian Standards Association since 1927. While developed independently from the NFPA code, is similar in scope and intent to the US NEC, with only minor variations in technical requirement details. Harmonization of the CEC and NEC codes is intended to facilitate free trade between the two countries.
Electrical wiring standards in Mexico follow that of the United States' NEC.
For residential wiring, some basic rules given in the NEC are:
The foregoing is just a brief overview and must not be used as a substitute for the actual National Electrical Code.
Electrical wiring practices developed in parallel in many countries in the late 19th and early 20th centuries. As a result, national and regional variations developed and remain in effect. Some of these are retained for technical reasons, since the safety of wiring systems depends not only on general technical standards for wiring, but also on those of wiring devices, materials, and equipment.
In North America the most common form of electrical service to residential and small commercial properties is 120 V AC split-phase, whereby a 240 V single-phase supply is put through a transformer which is then centre-tapped, resulting in three wires â a central neutral and two hot legs on either side of it â with 240 V between the two hots, and each hot having 120 V to the centre-tapped neutral. This provides the option for each circuit in the property to be either 240 V (utilising both hot legs without the neutral), or 120 V (utilising one of the two available hot legs with the neutral).
Alternatively some properties, especially in commercial and industrial sectors, will alternatively have a three-phase supply, which will have three hot legs (phases) with 208 V between phases, and 120 V from each phase to neutral. Common three-phase configurations within a building are 208/120 V wye, 120/240 V centre-tapped delta and 480v/277 V wye. Lighting is usually fed by 277 V or 120 V.
In contrast the majority of the world uses a frequency of 50 Hz, and properties are simply supplied with either a 220-240 V AC single-phase supply, or a 400 V AC three-phase supply (400 V between phases, and 220-240 V phase to neutral), without any such centre-tapping. In a property supplied by single-phase, all circuits will be 220-240 V. Properties supplied with three-phase can choose whether each circuit uses all three phases, as suitable to supply industrial three-phase motors for example, or only one of the three phases (combined with neutral), as suitable for most circuits, such as those supplying normal domestic-type power sockets and lighting.
An older, but still widely used, high-leg delta system unique to North America uses three phases with 240 V phase-to-phase for motor loads, and 120 V for lighting loads by use of a centre-tapped transformer. Two of the phases are 120 V to neutral; The third phase, the "high leg" of the system (also referred to as the "wild leg"), has 208 V to neutral and is not usually used for single-phase connections, so is distinctively colored. For larger commercial installations, 277/480 V or 347/600 V three-phase is common.
Most circuits in modern North American homes and light commercial constructions are wired with non-metallic sheathed (NM) cable. This type of cable is low cost and appropriate for dry indoor applications. The designation NM XX-Y indicates, respectively, the type of sheathing (in this case, non-metallic), the size of the main conductors, and the total number of circuit conductors (exclusive of the grounding conductor). For example, NM 14-2 cable contains three conductors (two plus one ground) at 14 gauge, a size typically used for circuits protected at 15 amperes. Circuits with larger currents (such as for electric furnaces, water heaters, air conditioners, or sub-mains to additional circuit panels) will have larger conductors. Not all US jurisdictions permit use of non-metallic sheathed cable. The NEC does not permit use of NM cable in large, fire-resistant, or high-rise structures.
In type NM cable, conductor insulation is color-coded for identification, typically one black, one white, and a bare grounding conductor. The US NEC specifies that the black conductor represent the hot conductor, with significant voltage to Earth; the white conductor represent the neutral conductor, near ground potential; and the bare/green conductor is the safety grounding conductor not normally used to carry circuit current. Wires may be re-colored, so these rules are commonly excepted. In 240-volt applications not requiring a neutral conductor, the white wire may be used as the second hot conductor, but must be recolored with tape or by some other method. Four-wire flexible equipment connection cords have red as the fourth color. Unlike older European practices, color-coding in flexible cords is the same as for fixed wiring.
In commercial and industrial, unenclosed NM cable is often prohibited in certain areas or altogether (depending on what the building is used for and local/state building codes), therefore this option is almost never used by commercial electrical contractors. Most wiring is put in non-flexible conduit, usually EMT because of its cost and durability. Rigid conduit may be required for certain areas. Vapor-lock fittings may be required in areas where a fire or explosion hazard is present (such as gas stations, chemical factories, grain silos, etc). PVC can be used where wire is run underground or where concrete will be poured. A duct bank is usually made of multiple PVC conduits encased in concrete. FMC or Flex is used where EMT or other non-flexible conduit is impractical or for short runs, known as "whips", to lights or other devices. For power circuits, the color-coding uses the same colors as residential construction, and adds the additional wires used for three-phase systems. Black, Red and Blue are used for hot wires and White is used as the neutral wire in a 120/208 V circuit. Brown, Orange and Yellow are used as hot wires and gray is used as the neutral wire in a 277/480 V. For grounding, regardless of the voltage, Green (or a bare wire) is used.
Several other types of wiring systems are used for building wiring in the United States; these include corrugated metal armored cable, mineral-insulated cable, other types of power cable, and various types of electrical conduit. In industrial applications cables may be laid in cable trays. Cable type TC is especially intended for use in tray systems. Special wiring rules apply to wet or corrosive locations, and to locations which present an explosion hazard. Wiring materials for use in the United States must generally be made and tested to product standards set by NEMA and Underwriters Laboratories (UL) and must bear approval marks such as those set by UL.
Approved wiring types can vary by jurisdiction. Not all wiring methods approved in the NEC are accepted in all areas of the United States.
When running through conduit, such as in commercial applications, it is typical to pull single-core wires rather than multicore cables.
Wire is manufactured in a range of conductor sizes, stranding, and materials (copper or aluminum), but the term "wire type" usually refers to the insulation, which determines the environments in which the wire may be used.
Wire types for North American wiring practices are defined by standards issued by Underwriters Laboratories, the Canadian Standards Association, the American Society for Testing and Materials, the National Electrical Manufacturers Association, and the Insulated Cable Engineers Association.
One important property of a cable affecting its current-carrying capacity is the maximum temperature rating of its insulation. Wire size, in combination with environmental factors affecting heat dissipation, such as ambient temperature and building insulation, determine the amount of tolerable copper loss in the wire, and therefore tolerable load current.
The most commonly used insulation type in AC electrical distribution systems throughout North America is THHN ("Thermoplastic High Heat-resistant Nylon-coated"). This is a specification for PVC insulation (other thermoplastics are permitted, but rarely used) with a nylon jacket for abrasion resistance. THHN is suitable for dry or damp environments and conductor temperatures up to .
A second popular type is THWN ("Thermoplastic Heat and Water-resistant Nylon-coated"). This is similar to THHN, but rated for dry or wet environments and conductor temperatures up to , and is commonly used in subsurface conduits which may fill with water.
A lot of THWN wire is actually dual-rated, meeting the THHN specification too, thus may be used in both wet environments up to , or dry environments up to .
An extended specification, THWN-2 permits use in wet locations and conductor temperatures up to 90 ðC simultaneously.
There are additional restrictions on such wire's use not mentioned here, for example, neither THHN nor THWN may be exposed to sunlight, or directly buried in the ground.
XHHW-2 (XLPE High Heat-resistant Water-resistant") is a less commonly seen insulation type with a thermoset plastic insulation. It has the same moisture and temperature specifications as THWN-2 (the original XHHW was equivalent to THHN/THWN dual-rated insulation), but being a thermoset plastic, it is less affected by temperature, remaining firmer at high temperatures and significantly more flexible at low temperatures. This makes it popular for outdoor wiring applications. The low dielectric constant of the insulation is also beneficial when high-frequency AC is present on the wire, such as the output of variable-frequency drives.