ESTCube-1 is the first Estonian satellite and first satellite in the world to attempt to use an electric solar wind sail (E-sail). It was launched on 7 May, 2013, aboard Vega VV02 carrier rocket and successfully deployed into the orbit. The CubeSat standard for nanosatellites was followed during the engineering of ESTCube-1, resulting in a 10ÃÂ10ÃÂ11.35 cm cube, with a volume of 1 liter and a mass of 1.048 kg.
The mission officially ended on 17 February, 2015. At that time, data from the satellite was used in 29 bachelor's and 19 master's dissertations, 5 doctoral theses, and 4 start-ups. The deployment of the E-sail tether was unsuccessful, and thus no measurements were taken of the E-sail or of the plasma braking deployment system. The last signal from ESTCube-1 was received on 19 May, 2015.
Developed as part of the Estonian Student Satellite Program, ESTCube-1 was an educational project in which university and high school students participated.
While emphasis was placed on educating students during creation of ESTCube-1, it did have a scientific purpose. The satellite carried an electric solar wind sail (E-sail), which was invented by Finnish scientist, Pekka Janhunen. During the ESTCube-1 flight, 10 meters of 20âÂÂ50 micrometer thick E-sail wire, sometimes referred to as "Heytether," were to be deployed from the satellite. The deployment of the Heytether was to be detected by a decrease of the satellite's rotation speed or an on board camera.
To control the E-sail element's interaction with both the plasma surrounding the Earth and the effect it had on the spacecraft's spinning speed, two nanotechnology electron emitters/guns were on board. The electron emitters were connected to the E-sail element which was to be charged positively to 500 volts by shooting out electrons. The positive ions in the plasma were intended to push the E-sail element and influence the satellite's rotation speed. The effect of the plasma on the E-sail was to be measured by the change in said rotation speed. The tether had also been intended to de-orbit the satellite by use as a plasma-brake to demonstrate a possibility for returning small satellites from orbit. A color CMOS camera was also on board that was capable of making RAW-format pictures with VGA-resolution. This camera was used to acquire images of Earth and had been intended to monitor deployment of the Heytether.
To complete the scientific experiment and communicate with the satellite on several occasions the orbit chosen was a SunâÂÂsynchronous circular orbit at an altitude of 670 kilometers. ESTCube-1 was launched into orbit by Arianespace, using Vega VV02 rocket which lifted off from ELA-1 at Kourou at 02:06:31 UTC on 7 May 2013. The satellite was placed into orbit and communication successfully established, with the first photo of the Earth taken on May 15, and transmitted to the ground on the amateur radio band.
The plan, beginning with the 7 May 2013 launch, included the following steps:
The mission ended due to degradation of the photovoltaic power system and subsequently the batteries became exhausted. The last official transmission was transmitted on 17 February, 2015, however, imaging the Earth and gathering telemetry data continued till May 19, 2015. The plan to test a solar sail the satellite carried failed since the sail cable unwinding mechanics did not survive the rocket takeoff vibration.
<imagemap> File:ESTCube-1 orbiting our colourful planet.jpg|alt=A grid of satellite photos of Earth, four wide by three high, on a black background.|center|thumb|600px|Photos taken by ESTCube-1 (in chronological order). Point at or click on each photo to see where it is.
rect 174 75 814 556 Arctic rect 844 75 1484 556 Australia rect 1514 75 2154 556 Brazil
rect 2180 75 2500 315 Bangladesh rect 2500 75 2820 315 Myanmar rect 2180 315 2820 556 Bay of Bengal
rect 174 586 814 1065 Algeria
rect 844 586 1484 1065 Peru
poly 1970 1065 2030 1040 2120 820 2154 850 2154 1065 Mauritania poly 1845 685 1790 830 1670 950 1650 930 1670 870 1735 810 1730 790 1770 740 1755 735 1800 660 1830 660 The Gambia circle 1980 670 30 Dakar poly 1970 1065 2030 1040 2120 820 1987 658 1845 685 1740 640 1514 1065 Senegal poly 1740 640 1690 760 1590 900 1514 840 1514 680 1650 635 Guinea-Bissau poly 1590 900 1514 1065 1514 840 Guinea
rect 1514 586 2154 1065 Atlantic Ocean rect 2180 586 2820 1065 Red Sea
rect 174 1096 814 1575 Sudan rect 844 1096 1484 1575 English Channel rect 1514 1096 2154 1575 Antarctica
rect 2180 1096 2820 1575 ChinaâÂÂMongolia border
</imagemap>
During the development of the Estonian satellite mission it was decided to make a 1U CubeSat. By standard 1 unit (1U) CubeSat base side length must be 100.0ñ0.1 millimeters and satellite height must be 113.5ñ0.1 mm. Mass is also set in CubeSat standard, the highest possible mass for 1U CubeSat is 1300 grams.
Communication from the satellite was made at two International Amateur Radio Unions registered frequencies
Periodic but very slow communication was made by using 18 WPM telegraphy signal on a frequency of 437.250 MHz. At that frequency, the most important satellite parameters are returned every 3 to 10 minutes. For fast connections FSK-modulation radio signals on a frequency of 437.505 MHz with a 9600 baud connection speed and AX.25 packet standard is used. The relatively slow connection speeds result from the use of amateur radio frequencies which limits the bandwidth to 25 kilohertz. The fast connection is used only when the satellite has been given a specific order. Both telegraphy and packet telemetry protocols of ESTCube-1 are published on project webpage.
Commands sent to the satellite used the 145 MHz (2 meter) amateur band.
ESTCube-1 microcontrollers used the following operating systems:
Mission Control System was developed by the students of Tartu University under the supervision of the company CGI Group.
ESTCube-1 was launched as a secondary payload onboard Vega flight VV02, the least expensive satellite launch offered by the European Space Agency. Because Estonia is an associated member of ESA, most of the launch expenses (about 70,000 euros) were covered by the Estonian member fee for educational expenses. With the launch, total expenses for the project were approximately 100,000 euros.
During its two-year operational life, ESTCube-1 satellite demonstrated the operation of the systems in space and successfully fulfilled most of its planned goals.